Το AriesRc.gr χρησιμοποιεί cookies για να προσφέρει καλύτερη εμπειρία χρήστη και σας συνιστούμε να δεχτείτε τη χρήση τους για να απολαύσετε πλήρως την πλοήγησή σας.

Ρυθμίσεις cookies
> >>>1PCs 10V~32V 12V 24V 480A Bidirectional Brushed 3S~6S ESC

Brushed ESC

Κατασκευαστές

Πληροφορίες

Προσφορά 1PCs 10V~32V 12V 24V 480A Bidirectional Brushed 3S~6S ESC Μεγαλύτερη προβολή

1PCs 10V~32V 12V 24V 480A Bidirectional Brushed 3S~6S ESC

1PCs 10V~32V 12V 24V 480A Bidirectional Brushed 3S~6S ESC

Περισσότερες λεπτομέρειες

Διαθέσιμο

65,00 € με Φ.Π.Α

-5,00 €

70,00 € με Φ.Π.Α

Άλλες πληροφορίες

HC480A Type 3: 480A XT60 connector, climbing car model
HC480A Type 4: 480A XT60 Connector, no Brake model

 

Description:

- Support model tanks, crawlers, boats. 2 ESCs are needed.

- Do not use while charging, the total length of the power cord should not exceed 20CM.

- When the ESC removes the MOS tube, it will heat up about 12A when it is fully opened in a single test. It is divided into 4 groups of tubes (that is, the sum is divided by 4).

- Power line: V+ (positive) V- (negative) 

- Motor line: M+ M-

 

Crawler mode: 

Automatically stop the motor after the throttle is back. (When the motor rotates forward, the throttle will pull back and the motor will immediately reverse)

 

No brake mode: 

After the throttle is back, the motor can rotate by inertia. (When the motor rotates forward, the throttle will pull back and the motor will immediately reverse)

 

Specification:

- UBEC: 5V 2A (Power supply to the receiver and servo)

- Weight: 65-70g

- Signal interface: around 20cm long wire

- Control switch: around 20cm long wire 

- Power interface: XT60, or without interface

- Motor interface: XT60, or without interface

- Size: 5CM*3.5CM*2.9CM

 

HC480A:

- Working voltage: 10V-32V (Lipo 4-7S), support 24V storage battery

- Continuous/peak current: 50A/480A forward, 50A/480A back

- Wire: power line and motor line 14AWG-100mm

- Supported motors: 24V less than 12000rpm 540/550775/795 brush motor, only used by motor within 12000rpm, connect with only one  motor.(Note: It is the motor's own speed, not the speed after the gearbox. )

 

HC960A:

- Working voltage: 10V-32V (Lipo 4-6S), support 24V storage battery

- Continuous/peak current: 100A/960A forward, 100A/960A back

- Wire: power line and motor line 12AWG-100mm

- Supported motors: brush motors, like 540/550/775/795/D848. For the motor under 10000, it can only connect 2 motors. (Note: It is the speed of the motor itself, not the speed after the gearbox)

E.G. When the motor rotate 10000 at 16V, it can conncet 2 motors when with 16V. It can NOT connect the battery above 16V)

 

Indicator status:

- After the ESC is powered on, the indicator light flashes once, and the indicator flashes again after the remote control is centered.

- After the signal is lost, the indicator light will flash quickly.

 

Correct stroke method: 

After the maximum stroke of the remote controller is reached, the ESC power-on indicator lights up and flashes again, and then the signal is inserted into the corresponding channel of the receiver. Wait for a few seconds, the indicator flashes twice, then the remote control is centered, and the indicator flashes three times.

 

Package included:

1PCs * ESC

 

61749-2